| Submitted | Field | Original | Note / Status | |
|---|---|---|---|---|
No corrections yet. Use the flag at the end of a row to report an issue. | ||||
Automatic mm / inch conversion · Core engineering specifications
| Overall dimensions | 3000 x 3000 x 2560 mm | |
|---|---|---|
| Canopy diameter | 3000 mm | |
| Canopy edge clearance height | 1980 mm | |
| Main support pole diameter | 48 mm | |
| Curved support arm length | 2100 mm | |
| Canopy rib length | 1500 mm | |
| Rib count | 8 | |
| Top wind vent diameter | 400 mm | |
| Adjustment joint spacing on pole | 650 mm | |
| Base fill port diameter | 80 mm | |
| Primary Component Thickness | 40 mm according to load-bearing role | |
| Hardware / Moving-part Clearance | 5 mm operating clearance |
Net weight / load capacity / users / durability
| Total filled base weight | 104 kg | |
|---|---|---|
| Umbrella net weight (excluding filled base) | 30 kg | |
| Total shaded area | 7.1 sqm | |
| Canopy fabric weight | 240 gsm | |
| Fabric colorfastness rating | Level 4 | |
| Recommended maximum sustained wind speed | 38 km/h | |
| Adjustment joint locking load rating | 120 kg | |
| Tilt adjustment angle range | 45 degrees | |
| Integrated weighted base dimensions | 1000 x 800 x 200 mm | |
| Reference Static Load | 150 kg depending on category |
Core acceptance fields · Panels / hardware / frame / upholstery
| Main support pole | 1.2mm thick powder-coated silver steel | |
|---|---|---|
| Curved offset arm | 1.0mm thick powder-coated silver steel | |
| Canopy support ribs | 0.8mm thick rectangular powder-coated steel | |
| Canopy fabric | 240gsm solution-dyed beige polyester | |
| Adjustment hardware | Injection-molded black nylon with steel locking pins | |
| Integrated base | High-density polyethylene (HDPE), black, fillable with sand or water | |
| Canopy hub connector | Glass-reinforced black nylon | |
| Canopy edge tips | Injection-molded black plastic caps | |
| Top wind vent mesh | Polyester mesh | |
| Frame finish | Matte silver polyester powder coating | |
| Primary Connector Specification | Reference M6-M10 with at least 2 fixing points at major joints | |
| Reference Finish / Color Count | Recommended 6finish options |
Adjustment / rotation / tilt / mobility / storage features
| Crank lift mechanism | Side-mounted crank raises and lowers canopy with smooth gear operation | |
|---|---|---|
| Infinite tilt adjustment | Dual locking joints allow 45degree canopy tilt with positive lock | |
| 360-degree rotation | Swivel joint at pole base allows full rotation around vertical axis | |
| Wind pressure relief | Top center vent allows air flow to reduce canopy lift in gusty conditions | |
| Base stabilization | Fillable base accepts water or sand to counterbalance offset canopy load | |
| Storage tie strap | Attached Velcro strap secures folded canopy when not in use | |
| Locking mechanism | Spring-loaded locking pins secure adjusted tilt and rotation positions | |
| Reference Adjustment / Operating Range | 100 mm or 120° where applicable |
Verified carton / gross weight / assembly / loading data
| Reference Package Count | 1 set / 2 cartons | |
|---|---|---|
| Reference Assembly Time | 40 minutes per set | |
| Reference Packaging Volume | 0.8 m³/set | |
| Reference Packaged Gross Weight | 120 kg/set |
Recommended spaces / users / usage modes
| Residential patio seating | Provides shade over 4-person outdoor dining or lounge sets | |
|---|---|---|
| Backyard poolside use | UV-resistant fabric and rust-proof frame suit humid, wet pool environments | |
| Garden leisure areas | Adjustable tilt tracks sun movement across garden seating zones | |
| Small commercial cafe seating | Stable weighted base works for outdoor bistro table setups without permanent mounting | |
| Balcony shade installation | 3m diameter fits standard large residential balcony footprints |
EU Market Access Requirements* EN Standards
| EN 13561:2015 | Applies to external sunshade performance, wind resistance, and safety requirements |
|---|
Standards applicable to China-market projects
This product must meet the following technical requirements: 1. Technical standards and test reports must be supplied during tender or purchase confirmation; Final delivery parameters, test reports, and acceptance criteria are subject to the purchase contract.
Export data is generated from the current published product record.
Directly download an English report in metric or imperial units.
Download all product information and parameter modules in English.
English title, specifications, materials, standards and purchasing fields.
Prepare customs description, material, usage, dimensions and declaration elements.
Open Export Tool
