| Submitted | Field | Original | Note / Status | |
|---|---|---|---|---|
No corrections yet. Use the flag at the end of a row to report an issue. | ||||
Automatic mm / inch conversion · Core engineering specifications
| Overall dimensions | 1500 x 800 x 560 mm | |
|---|---|---|
| Tabletop sintered stone thickness | 12 mm | |
| Embedded heating tray dimensions | 600 x 300 mm | |
| Central cabinet module dimensions | 800 x 280 x 400 mm | |
| Metal frame leg tube cross-section | 50 x 30 mm | |
| Undertable floor clearance | 120 mm | |
| Front control panel button spacing | 20 mm | |
| Perforated vent opening diameter | 15 mm | |
| Tabletop edge overhang past frame | 40 mm | |
| Tempered glass side panel thickness | 8 mm | |
| Frame vertical leg height | 520 mm | |
| Lower frame crossbar height from floor | 120 mm | |
| Primary Component Thickness | 40 mm according to load-bearing role | |
| Hardware / Moving-part Clearance | 5 mm operating clearance |
Net weight / load capacity / users / durability
| Tabletop uniform static load capacity | 100 kg | |
|---|---|---|
| Embedded electric heating unit maximum power | 2000 W | |
| Sintered stone surface heat resistance | 1200 °C | |
| Sintered stone surface abrasion resistance | 6000 revolutions | |
| Product net weight | 68 kg | |
| Metal frame load-bearing cycle rating | 10000 cycles | |
| Anti-tip kit required for installation | 2 connectors | |
| Reference Static Load | 150 kg depending on category | |
| Moving-part Durability Reference | Acceptance target 50000 cycles | |
| Recommended Procurement Warranty | Structure 5 years; hardware 3 years |
Core acceptance fields · Panels / hardware / frame / upholstery
| Tabletop | 12mm sintered stone with marble-pattern polished finish | |
|---|---|---|
| Structural frame | Dark powder-coated cold-rolled steel tube with matte finish | |
| Central cabinet side panels | 8mm frosted tempered glass | |
| Central cabinet door panel | Matte black steel with perforated ventilation holes | |
| Control panel | Matte black steel plate with tactile push buttons | |
| Embedded heating tray | Black crystallized glass panel for induction heating | |
| Frame welds | Ground and powder-coated for seamless appearance | |
| Tabletop edge treatment | Rounded polished stone edge matching surface finish | |
| Cabinet drawer slides | Cold-rolled steel damped buffer slides | |
| Foot pads | Non-slip rubber pads to protect floor surfaces | |
| Edge banding for internal panels | 1mm PVC edge banding for concealed cabinet panels | |
| Heating unit housing | Galvanized steel internal enclosure for electrical components |
Adjustment / rotation / tilt / mobility / storage features
| Embedded heating function | Induction heating for tea kettle boiling, 2000W max power | |
|---|---|---|
| Front panel control | Tactile push buttons for power, temperature and timer adjustment | |
| Central cabinet storage | Enclosed compartment for tea accessories, water pump and waste bucket | |
| Ventilation system | Perforated side panel to dissipate heat from electrical components | |
| Easy-clean surface | Non-porous sintered stone top resists tea stains and water marks | |
| Stable open frame | Four-point metal frame support eliminates wobble on flat floors | |
| Automatic safety shutoff | Anti-dry burn protection cuts power when no water is detected | |
| Cable management | Internal routing for power cord to hide wiring under table | |
| Floor protection | Rubber foot pads prevent scratches on hard flooring and carpet | |
| Reference Adjustment / Operating Range | 100 mm or 120° where applicable |
Verified carton / gross weight / assembly / loading data
| Reference Package Count | 1 set / 2 cartons | |
|---|---|---|
| Reference Assembly Time | 40 minutes per set | |
| Reference Packaging Volume | 0.8 m³/set | |
| Reference Packaged Gross Weight | 120 kg/set |
Recommended spaces / users / usage modes
| Living room seating area | Placed in front of sofa for tea preparation and serving during social gatherings | |
|---|---|---|
| Executive office reception area | Used to serve tea to visiting guests in formal office settings | |
| Tea room dedicated space | Installed as primary brewing surface for home or commercial tea rooms | |
| Light luxury interior schemes | Matches marble, dark metal and neutral tone modern design palettes | |
| Residential open plan spaces | Suits open-concept living areas with low-profile, unobtrusive design | |
| Small group use | Accommodates up to 4 people seated around the table for tea service |
EU Market Access Requirements* EN Standards
| EN 12521:2015 | Safety, strength and durability requirements for domestic tables | |
|---|---|---|
| EN 60335-1:2012 | Safety of household electrical appliances for embedded heating components | |
| EN 14372:2004 | Surface resistance to abrasion and heat for furniture worktops |
Standards applicable to China-market projects
| GB/T 3324-2017 | General technical requirements for wooden and composite furniture, applicable for cabinet components | |
|---|---|---|
| GB 4706.1-2005 | Safety of household electrical appliances, applicable for embedded heating unit | |
| GB/T 17657-2013 | Test methods for surface properties of furniture panels, applicable for sintered stone top | |
| GB 18584-2001 | Formaldehyde emission limit for furniture, ≤0.1mg/L E0 grade for internal panel components |
This product must meet the following technical requirements: 1. GB/T 3324-2017: General technical requirements for wooden and composite furniture, applicable for cabinet components; 2. GB 4706.1-2005: Safety of household electrical appliances, applicable for embedded heating unit; 3. GB/T 17657-2013: Test methods for surface properties of furniture panels, applicable for sintered stone top; 4. GB 18584-2001: Formaldehyde emission limit for furniture, ≤0.1mg/L E0 grade for internal panel components; Final delivery parameters, test reports, and acceptance criteria are subject to the purchase contract.
Export data is generated from the current published product record.
Directly download an English report in metric or imperial units.
Download all product information and parameter modules in English.
English title, specifications, materials, standards and purchasing fields.
Prepare customs description, material, usage, dimensions and declaration elements.
Open Export Tool
